Durable Digital Roll Label Cutting Machine

Maxi. roll diameter

450mm

Cutting media width

40--340mm

Max. label width

320mm

Max. label length

400mm (segmentation cut reach to 1200mm)

Mini. label length

10mm

Min. distance between labels

2mm

Min.distance from mark to edge

2mm

Min.distance between jobs

2mm

Max. die cutting speed

6m per minute (depends on label shape and size)

No. of die cutting heads

2pcs(standard ), up to 4pcs.

Die cutting blades

Tungsten steel blades

Die cutting precision

0.1mm (duplicate)

Die cutting mark track mode

Non-mark, Single mark,double mark

Slitting width

10 ~ 310mm

Slitting blades

4pcs(standard ), up to 15pcs

Slitting speed

100m/min

Slitting precision

0.1mm

Data transfer method

USB2.0/Ethernet 10/100Base-T/GPIO

Working voltage

110-240VAC 50/60HZ, 1000WATTS

Machine dimension

160*100*136cm(L*W*H)

Optional function

Multiple die cutting heads

Multiple slitting units

Film base paper   removing device

Roll to sheet cutter RS350

1

Multiple   die cutting heads.

VR320   works with multiple die cutting heads, up to 4 heads work at the same time, highly   increase working efficiency.

2

User   friendly operation panel.

The main   operation buttons are integrated into the same panel for easy operation.   Touch screen interface, sensitive response, easy to set machine parameters.

3

Digital   cutting positioning sensor.

The   positioning sensor scans the marked points printed on the material to obtain   the cutting dies information and feed it back to the machine control system,   so as to realize the digital cutting.

4

Automatic deviation correction system.

There are two optical sensors on both sides of roll holder,   automatically adjust the paper offset to ensure the accurate feeding, lay a   good foundation for further processing.

5

Feeding   detection system.

After   automatic deviation correction, there is an optical sensor to detect the   material before feeding into the working table, make sure the paper feeding   in correct way, ready for next die cutting step.

6

Vacuum suction cutting table.

Vacuum inhaling cutting platform, the adsorption function starts along   with die cutting, and automatically loosening valves after cutting   finishes,   to ensure cutting accuracy   and smooth paper feeding.

7

Platform for splicing materials.

When you finish cutting a roll of label and prepare to cut another   roll, you can use this platform to splice a new roll of material onto the one   being processed, so as to realize smooth transition, save paper installation   time and improve work efficiency.

8

Cold lamination.

Automatic lamination before die cutting, makes finishing labels more   durable and more widely application.

9

Automatic   waste removal and tension system.

Under the   tension of the waste discharge system, the label cutting waste paper will be   automatically removed and separated from the winding, so as to obtain a clean   label roll for the next process.

10

Slitting system.

Utilize square blades, automatically cut the label paper into small   rolls as needed,up to 15pcs blades can be used. Maximum slitting speed can   reach to 100m/min.

11

Automatic separate rewinding.

Up and down independent winding shafts, automatically rewind the   multiple label rolls after slitting.

12

Well-organized control cabinet.

Professional electrical design, orderly arrangement of components,   clear circuit, easy maintenance.

13

Blower switch.

Control the suction system. Before die cutting, press this button to   start the vacuum adsorption function.

14

Network and USB Port.

VR320 roll label cutter supports network port and U disk for die   cutting files transmission.

15

E-stop button.

If any emergency happens during machine working, press this button, the   machine will stop instantly.You need to turn on the power to restart the   machine.

16

Quality components.

All kinds of components used in VR320 are top quality in the industry,   such as THK precision class guide rail, imported synchronous belts, Inovance   servo motor, etc. Ensures machine quality and longer service life.

17

Adjustable machine foot pads.

VR320 is equipped with adjustable foot pads and mobile wheels. If the   ground is uneven, the horizontal position of the machine can be ensured by   adjusting the foot pads. A movable wheel is installed beside each foot pad   for more convenient machine movement.

18

Easy-to-use software.

Dedicated software support PLT & DXF format file, it can choose the   knife down point according to shapes, the unique trajectory optimization is   for perfect cutting.

19

Maximum   four cutting heads.(optional)

The   standard cutting heads for VR320 is 2pcs, user can choose maximum four die   cutting heads as required.

20

Film base   paper removing device.(optional)

In some   areas, there is backing paper on the cold laminating film, which can be   removed before laminating by this device.